[. . . ] INSTALLATION INSTRUCTIONS
BUILT-IN KIT MODELS
RK-93S27 RK-93S30
IMPORTANT: This Built-In Kit is designed for use with those Sharp Microwave Ovens specifying RK-93S27 or RK-93S30 Built-In Kit on rating label on the front of the oven. PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION!
PART NAME DUCT (A)-1 PDUC-0259WRW0 DUCT (A)-2 RK-93S27 PDUC-A330WRW0 RK-93S30 PDUC-A733WRW0 DUCT (A)-3 PDUC-A734WRW0 DUCT (B) PDUC-0260WRW0 DUCT (C) PDUC-A274WRW0 STOPPER RK-93S27 LSTPFA005WRW0 RK-93S30 LSTPFA008WRW0 CORD BOX FCOVHA010WRK0 SASH (T) RK-93S27 GWAKMA031WRE0 RK-93S30 GWAKMA033WRE0 SASH (S) RK-93S27 GWAKMA030WRE0 RK-93S30 GWAKMA032WRE0 CUSHION (A) PCUSU0322WRP0 CUSHION (B) PCUSUA531WRP0 SCREW (A) XCTSD40P08000 (one extra) SCREW (B) XMMSE41P20000
Q'TY 1 1 1 1 1 2 1 2 2 1 1 10 4
DUCT (A)-1
DUCT (A)-2
DUCT (A)-3
DUCT (B)
(FOR RK-93S30) (FOR RK-93S27)
DUCT (C)
CORD BOX
STOPPER
SASH (T)
CUSHION (B) (thick)
CUSHION (A) (thin)
SASH (S)
SCREW (A)
SCREW (B)
* For walls other than wood, you may need appropriate screws to install the SASH and STOPPER. [. . . ] ELECTRICAL SUPPLY At the rear of the opening, provide a 3 pronged, polarized, electrical outlet, 115-120 volt A. C. , 15 amp. OVEN SUPPORTS
5 Cement two 2" x 2" x 15 /8" wooden supports as indicated in Sketch 1. Follow contact cement instructions carefully.
1
STEP 2: INSTALLATION OF KIT
(a) Insert the edge of DUCT (B) into the hold lip of DUCT (C). Remove the existing screw (#1) at upper right rear of the oven and secure DUCT (C) with the screw (#1) just removed from the oven. Secure DUCT (B) with SCREW (A) through the duct and into the original screw hole in the oven. See Sketch 2.
2
2
(b) Position DUCT (A)-1 on the top of the oven inserting edge of DUCT (BC) into hold lip of DUCT (A)-1. See Sketch 3.
3
(c) Position DUCT (A)-2 on top of the oven and insert it into the hold lip of DUCT (A)-1. See Sketch 4.
4
(d) Position DUCT (A)-3 on top of the oven and insert it into DUCT (A)-2. See Sketch 5.
CUSHION (A)
5
3
STEP 3: CORD BOX
(a) Plug the oven electrical cord into the CORD BOX RECEPTACLE and roll the remaining part of the cord into the CORD BOX as shown in Sketch 6-(a). Using the screw #2 just removed from the oven, secure the CORD BOX to the oven. See Sketch 6.
6
STEP 4: INSTALLATION
(a) Place the oven with the right side on a flat surface. See Sketch 7.
BOTTOM PLATE
SCREWS
7
CUSHION (B)
(b) Return the oven to the original position. [. . . ] Secure the lower SASH (T) to the wall (or cabinet) through the lower hole in SASH (S) using a SCREW (B) provided. See Sketch 0.
!
6
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163 Phone: 1-800-BE-SHARP (237-4277)
TINSEB348WRRZ
8 [. . . ]